91精品国产麻豆国产自产在线_大香蕉琪琪色免费在线视频_性高朝久久久久久久久久_97久久精品亚洲中文字幕无码_精品久久久久久综合日本_精品久久久噜噜噜久久久_欧美国产日韩精品_亚洲欧洲日产国码av系列天堂_樱桃成人免费在线视频高清无码_91中文字幕午夜看片福利

On Semi 公司的NCV7381是單路FlexRay總線驅動器,和FlexRay電物理層指標Rev.3.0.1兼容,通信速度高達10Mbps,在有線的FlexRay通信中提供差分通信媒界,具有極好的EMC和ESD性能,工作溫度−40°C 到+125°C,符合汽車級質量標準.本文介紹了NCV7381主要特性,框圖和應用框圖,FlexRay總線驅動器應用電路圖以及NCV7381 APP V2評估板主要特性,框圖,電路圖,元件清單和PCB布局圖.

NCV7381 is a single−channel FlexRay bus driver compliant with the FlexRay Electrical Physical Layer Specification Rev. 3.0.1, capable of communicating at speeds of up to 10 Mbit/s. It provides differential transmit and receive capability between a wired FlexRay communication medium on one side and a protocol controller and a host on the other side. NCV7381 mode control functionality is optimized for nodes permanently connected to car battery.

It offers excellent EMC and ESD performance.

NCV7381主要特性:

General

• Compliant with FlexRay Electrical Physical Layer Specification Rev 3.0.1

• FlexRay Transmitter and Receiver in Normal−power Modes for Communication up to 10 Mbit/s

• Support of 60 ns Bit Time

• FlexRay Low−power Mode Receiver for Remote Wakeup Detection

• Excellent Electromagnetic Susceptibility (EMS) Level over Full Frequency Range. Very Low Electromagnetic Emissions (EME)

• Bus Pins Protected against >10 kV System ESD Pulses

• Safe Behavior under Missing Supply or No Supply Conditions

• Interface Pins for a Protocol Controller and a Host (TxD, RxD, TxEN, RxEN, STBN, BGE, EN, ERRN)

• INH Output for Control of External Regulators

• Local Wakeup Pin WAKE

• TxEN Time−out

• BGE Feedback

• Supply Pins VBAT, VCC, VIO with Independent Voltage Ramp Up:

♦ VBAT Supply Parametrical Range from 5.5 V to 50 V

♦ VCC Supply Parametrical Range from 4.75 V to 5.25 V

♦ VIO Supply Parametrical Range from 2.3 V to 5.25 V

• Compatible with 14 V and 28 V Systems

• Operating Ambient Temperature −40°C to +125°C (TAMB_Class1)

• Junction Temperature Monitoring with Two Levels

• SSOP−16 Package

FlexRay Functional Classes

• Bus Driver Voltage Regulator Control

• Bus Driver – Bus Guardian Interface

• Bus Driver Logic Level Adaptation

• Bus Driver Remote Wakeup Quality

• Automotive Qualification According to AEC−Q100 (Rev. F)

圖1.NCV7381框圖

圖2.NCV7381應用框圖

NCV7381 APP V2評估板

This document describes the NCV7381 APP V2 Evaluation board for the ON Semiconductor NCV7381 FlexRay Bus Driver. The functionality and major parameters can be evaluated with the NCV7381_APP_v2 board.

The NCV7381 is a single-channel FlexRay bus driver compliant with the FlexRay Electrical Physical Layer Specification Rev. 3.0.1, capable of communicating at speeds of up to 10 Mb/s. It provides differential transmit and receive capability between a wired FlexRay communication medium on one side and a protocol controller and a host on the other side.[由88ffaa.com編輯]

NCV7381 mode control functionality is optimized for nodes permanently connected to car battery.

The NCV7381_APP_V2 Evaluation board is a reference design for stand-alone 2-channel FlexRay node. The board is intended to give designers easy, quick and convenient means for evaluation of NCV7381 FlexRay bus drivers. The design incorporates complete node solution with possibility of modifications and small board size. A set of two boards allows users immediately start with the NCV7381 FlexRay Bus Driver. The MCU is preprogrammed with a firmware which provides simple mode control and FlexRay communication. With use of Freescale[1] BDM programmer and a suitable development environment, the MCU firmware can be freely modified and reprogrammed.

Board Hardware

The board consists of MCU with integrated 2-channel FlexRay communication controller interconnected with two separate FlexRay bus drivers (NCV7381), two switchable voltage regulators and peripherals. The board is prepared for various modifications in power supply concept and FlexRay bus termination, and allows simple extension of the system by unused MCU pins. USB interface provides compatibility with standard PC. The address of each board can be easily modified by address switch what allows creating complex FlexRay network without need of reprogramming the MCU.

Implemented High Speed CAN interface can be used as a diagnostic interface in a network built from several nodes. For evaluation purposes NCV7381 is populated with several LED diodes and most of the bus driver signals are comfortable accessible to oscilloscope probes.

NCV73812037EVB評估板主要特性:

FlexRay Transceiver

 Two Separate FlexRay Channels with NCV7381 Bus Driver Compliant with the FlexRay Electrical Physical Layer Specification Rev. 3.0.1

 Reconfigurable Bus Termination – End Node/Middle Node

 Common Mode Choke and Additional ESD Protection Footprint

 SUBD-9 Connectors – FlexRay bus

 Local Wakeup Switch

MCU

 Freescale[1] 16-bit MC9S12XF Family MCU

 Integrated FlexRay Communication Controller (Protocol Specification Rev. 2.1)

 Integrated CAN 2.0 A, B Controller

 Background Debug Modul – Single-wire Communication with Host Development System

 512 kB Flash

 32 kB RAM

 50 MHz Maximum CPU Bus Frequency

 Relatively Small 112-pin LQFP Package

Peripherals

 Optical Isolated USB Interface (USB to UART Converter)

 Additional CAN Interface

 All NCV7381 Digital I/O Pins Connected to Test Points – Easy Connection to Logic Analyzer

 8 General Purpose LEDs

 Address Switch

Other

 Two Automotive Voltage Regulators with Inhibit Function (Input Battery Voltage Up to 42 V)

 Power Supplies Voltage Monitoring

 Instant 2-nodes FlexRay Network with Running Communication by Connecting Two NCV7381 EVBs

 PC Configuration Software under Development (Available upon Request)PCB Layout

 The FlexRay Transceiver, the ESD Protection and the Common Mode Choke are Placed near to the FlexRay the ECU

Connector

 The FlexRay Signal Lines (BP, BM) are Decoupled from Disturbances on the ECU Board

 The Routing of the FlexRay Lines (BP, BM, TX and TXEN) is Symmetric

圖5.NCV7381 APP V2評估板框圖

圖6.NCV7381 APP V2評估板電路圖

NCV7381 APP V2評估板材料清單(BOM):

圖標:

1 Power Supply Input Connector 9 FlexRay BD Signals Test Points (Channel A)

2 Aux Digital I/O Connector 10 FlexRay BD Signals Test Points (Channel B)

3 CAN Backbone Connector 1 11 MCU Reset Switch

4 CAN Backbone Connector 2 12 MCU External Interrupt Switch

5 USB Interface 13 BD Local Wakeup Switch (Channel A)

6 Address Switch 14 BD Local Wakeup Switch (Channel B)

7 FlexRay CC Strobe Output Signals 15 FlexRay Bus Connector (Channel A)

8 BDM Connector (MCU Debugging Interface) 16 FlexRay Bus Connector (Channel B)

9 FlexRay BD Signals Test Points (Channel A)

10 FlexRay BD Signals Test Points (Channel B)

11 MCU Reset Switch

12 MCU External Interrupt Switch

13 BD Local Wakeup Switch (Channel A)

14 BD Local Wakeup Switch (Channel B)

15 FlexRay Bus Connector (Channel A)

16 FlexRay Bus Connector (Channel B)

圖8.NCV7381 APP V2評估板元件布局圖(頂層)

圖9.NCV7381 APP V2評估板元件布局圖(底層)

圖10.NCV7381 APP V2評估板PCB布局圖(頂層)

PDF資料參考:
http://www.onsemi.cn/pub_link/Collateral/NCV7381-D.PDF

http://www.onsemi.cn/pub_link/Collateral/EVBUM2037-D.PDF

http://www.onsemi.cn/pub_link/Collateral/NCV73810V2GEVB_SCHEMATIC.PDF